Shimano bearing part# for 3x7x3mm
Shimano bearing part# for 3x7x3mm
I am helping a friend to buy shimano stock spool bearing for 01 calcutta conquest 50.
For this reel and othet small reels, shimano uses a small bearing 3x7x3 at the tension knob side.
Check the schematic from shimanon US site but cannot find a part# just for this bearing, but a whole spool assembly including the bearing.
Can someone show a part# for 3x7x3 bearing only so we can order directly from shimano?
Thanks
Ben
For this reel and othet small reels, shimano uses a small bearing 3x7x3 at the tension knob side.
Check the schematic from shimanon US site but cannot find a part# just for this bearing, but a whole spool assembly including the bearing.
Can someone show a part# for 3x7x3 bearing only so we can order directly from shimano?
Thanks
Ben
Ben ...the shimano fan
Re: Shimano bearing part# for 3x7x3mm
Did you look at Boca?
Re: Shimano bearing part# for 3x7x3mm
Tommy,
Thanks for reply my 1st post.
Yeah, I believe boca or hedgehog has the size we need but prefer the stock beering. If we can't source it from shimano then we have to go to these brands
Thanks for reply my 1st post.
Yeah, I believe boca or hedgehog has the size we need but prefer the stock beering. If we can't source it from shimano then we have to go to these brands
Ben ...the shimano fan
Re: Shimano bearing part# for 3x7x3mm
I need to know OD x ID x W to check my bearing chart. I know some of the bearings we never received a part number or replacement bearings for due to low demand.
Re: Shimano bearing part# for 3x7x3mm
Hi Bantam,Bantam1 wrote:I need to know OD x ID x W to check my bearing chart. I know some of the bearings we never received a part number or replacement bearings for due to low demand.
the dimension is on the title, 3 (ID) x7 (OD) x3 (W) mm, thank you!
Ben ...the shimano fan
Re: Shimano bearing part# for 3x7x3mm
I checked my bearing size list and can't find any bearing that matches the dimensions you listed. This is one of the bearings we never received a part number for and required the spool to be replaced if it needed a bearing. In this case you will have to use an aftermarket bearing unfortunately. The closest bearing we have in size is 7 x 4 x 2.5 (OD x ID x W).
We have bearings for the CTE50GT.
We have bearings for the CTE50GT.
Re: Shimano bearing part# for 3x7x3mm
Bantam,Bantam1 wrote:I checked my bearing size list and can't find any bearing that matches the dimensions you listed. This is one of the bearings we never received a part number for and required the spool to be replaced if it needed a bearing. In this case you will have to use an aftermarket bearing unfortunately. The closest bearing we have in size is 7 x 4 x 2.5 (OD x ID x W).
We have bearings for the CTE50GT.
could you help to double check if BNT2810 is the same size I am looking for? it's from CTE50GT I believe.
thanks
Ben
Ben ...the shimano fan
Re: Shimano bearing part# for 3x7x3mm
The part number BNT2810 is the 3x7x3 spool bearing from under the cast control cap of the CTE50GT.
https://www.ebay.com/itm/Shimano-Ball-B ... 2930661648
https://www.ebay.com/itm/Shimano-Ball-B ... 2930661648
Re: Shimano bearing part# for 3x7x3mm
That bearing is discontinued.
Re: Shimano bearing part# for 3x7x3mm
ThanksZimbass wrote:The part number BNT2810 is the 3x7x3 spool bearing from under the cast control cap of the CTE50GT.
https://www.ebay.com/itm/Shimano-Ball-B ... 2930661648
Ben ...the shimano fan
Re: Shimano bearing part# for 3x7x3mm
Oops... too bad.. seems we have to get after market bearings.Bantam1 wrote:That bearing is discontinued.
Thank you Bantam
Ben ...the shimano fan