Working on Reels - Tips!

Here's your chance to speak directly with the TT Gear Crew. Post your questions, comments, experiences regarding tackle maintenance and super tuning
User avatar
LPFC
Elite Angler
Elite Angler
Posts: 400
Joined: Thu Nov 17, 2011 10:31 pm
Location: Lake Parsippany, NJ

Re: Working on Reels - Tips!

Postby LPFC » Thu Mar 08, 2012 10:42 pm

When I remvoe the bearing retaining clips, I use one of those Turkey baking bags. It's big enough to work in.

I also found something to help find those clips that fly and screws that screw ya, lol

The magnet that car dealers use to attach license plates to cars. Like the one's they put on cars when you take a test drive.

Also for tools, at Home Depot, Husky has little tool sets that come in case. Red bottom clear lid. There inexpensive. 1 has fine screw driver bits and a handle, one has a stuby rachet screw driver handle with bit's and a small socket set. These all cost me like $10 on sale but I think there like $5 a set. These have covered every screw and most nuts I have come across.

Note books are great to keep with the schmatic's. There was a suggestion of downloading each schmatic which is a great idea. Something to add, you can find a very cheap older laptop to keep at your repair station. No need for any special software. Just connected it to the internet one time and download all the schmatic's you need. Then disconnect it. This way your not using the computer your kids or wife is using. Your own personal data base of reels.
Then you will also always have NOTE PAD to take notes. I hate when I can't find a pen, lol

You can also find a cheap camera and take pictures as you clean/repair. Walmart sells a USB SD card reader for like $10. Load the pictures onto your computer and enlarge the pictures so you could really see all the small parts.

Hope some of these tips help.

If you need any help with what can be remove from a computer to keep it minimum post back or shoot me an IM.

User avatar
Gabriel
Elite Angler
Elite Angler
Posts: 497
Joined: Wed Jan 11, 2012 1:28 am

Re: Working on Reels - Tips!

Postby Gabriel » Mon Jul 23, 2012 6:24 pm

I just have some simple things that haven't been mentioned for the most part.


Okuma Variable Oscillation systems on their spinning reels are very hard to work with because of an oblong oscillation drive gear. The main gear has a notch that lines up with the lowest part of the oscillation gear. Very difficult to do. Leave in while working on them. Oblong gears are sucky.

Shimano Reel Wrenches fit Daiwa reels.

Big clear tackle trays are very nice for working on reels. I put them in the slots in order of removal.

Original Super Stopper II Spinning Reel anti reverses can almost always be fixed by cleaning them. Especially on old Stradics. I run them dry, or as near dry as possible.

If a spinning reel has trouble reeling at the bottom end of the line wrapping there is almost always line wrapped inside the spool. Easy 1 minute fix.



Simple things that are good to know.
"Can I poke the fish in the eye?"
Dakota

ipoppa33
Senior Angler
Senior Angler
Posts: 122
Joined: Tue Jun 20, 2006 9:59 pm
Location: MA
Contact:

Re: Working on Reels - Tips!

Postby ipoppa33 » Tue Jul 24, 2012 10:27 am

Great tips, thank you.

jtakeman
Angler
Angler
Posts: 26
Joined: Sun Apr 08, 2012 4:49 pm

Re: Working on Reels - Tips!

Postby jtakeman » Tue Aug 14, 2012 3:18 pm

Thanks for the tips. Great thread!! =D>

User avatar
ztcsmd
Senior Angler
Senior Angler
Posts: 154
Joined: Sat May 26, 2012 9:21 am
Location: Texas Gulf Coast

Re: Working on Reels - Tips!

Postby ztcsmd » Mon Mar 04, 2013 12:45 pm

I will either down load schematics or use the one that came with reel and on a copy machine I enlarge to about 150% or enough to fill the entire page of a size 8-1/2" x 11" sheet of paper and do the same with the corresponding part number key on a separate sheet. I put both pages back to back and laminate them--easy to read without glasses and last forever, lay it on the work area when working on reels and don't have to worry about greasy fingers. Also use a green felt gun cleaning pad with rubber backing to avoid scratching reel paint surfaces and does not slide around. I utilize a 12 drawer top chest like a Proto or Craftsman in extra bedroom that I turned into a fishing room to keep all of my tools, cleaning supplies, parts and such in--also serves multi function purpose for bow hunting goodies and extra magazines, scopes and such for hunting....geez, now that I think about it--I think I may have a problem....

tosakilla
Senior Angler
Senior Angler
Posts: 73
Joined: Sun Jan 29, 2012 9:59 pm

Re: Working on Reels - Tips!

Postby tosakilla » Wed Mar 20, 2013 1:27 pm

most of the reels i work on have never been cleaned before and are pretty gross. one thing ive found is to take a tooth pick and dip it in simple green and really get into the gears, it has more force than a tooth brush with out the risk of scratching anything, and it gives you a nice fresh start.

beezy
Elite Angler
Elite Angler
Posts: 318
Joined: Fri Apr 01, 2011 7:11 pm
Location: So Cal

Re: Working on Reels - Tips!

Postby beezy » Thu Aug 01, 2013 12:48 pm

I have a question regarding Daiwa reels in general. What's the best method for removing and re-installing the clutch cam spring on these daiwa reels? I can clean the reel fine but when it comes to this piece, it totally blows my mind how hard it is to put back in sometimes. Any tips?

Lexy 123
Elite Angler
Elite Angler
Posts: 206
Joined: Thu Sep 06, 2012 8:51 am

Re: Working on Reels - Tips!

Postby Lexy 123 » Fri Sep 20, 2013 1:33 pm

great tips guys, thanks.

mark poulson
TT Pro Angler
TT Pro Angler
Posts: 1978
Joined: Thu Dec 20, 2007 6:28 am
Location: NoCal

Re: Working on Reels - Tips!

Postby mark poulson » Sun Jun 11, 2017 5:51 am

Use your cellphone to take pictures of each step as you tear down a reel, so you'll always know what went where, and lay to parts down in order as you remove them, so you'll know the proper sequence for reassembly.
You can email the cellphone pictures to yourself, so you can have them saved onto your computer.

Ripken_240
Newbie Angler
Newbie Angler
Posts: 3
Joined: Thu May 03, 2018 1:48 pm

Re: Working on Reels - Tips!

Postby Ripken_240 » Mon Nov 26, 2018 4:59 am

Awesome tips in here. Thanks guys. I usually send my stuff out but this will save me some extra coin for sure!

doug in co
Newbie Angler
Newbie Angler
Posts: 2
Joined: Fri Dec 07, 2018 11:49 am

Re: Working on Reels - Tips!

Postby doug in co » Fri Dec 07, 2018 12:56 pm

for tricky little springs etc, I usually disassemble in a shoebox. With any luck the spring will bounce off back into the box..

cellphone pics as already noted, for each step.

I have a set of Winchester gunsmith screwdrivers, also work well on reels.

work a lot on ancient gunked-up fly reels off the giant online flea market. For these, soak the parts in a small plastic tub with Finish Line Citrus Bicycle degreaser, seems to be a bit more effective and smells better than Simple Green or Purple. Scrub with toothbrush, rinse, lay out on newspaper, dry with paper towel, then use a hairdryer to warm everything up and make sure there isn't any residual moisture lurking.

most recently worked on a Heddon 320 fly reel. These have a teeny tiny little elbow spring in the latch cover, to latch the spool to the center pin. I forgot to get it out of the degreaser rinse tub.. took the tub to the utility sink, emptied, rinsed vigorously. Some time after that I looked at the parts and wondered where the spring was.. went back to the sink and it was still lying there, not down the drain. Either I should buy a lottery ticket, since the luck is clearly going my way: or hide in the basement, since I've clearly used up all my luck for the year..

User avatar
uljersey
Platinum Angler
Platinum Angler
Posts: 1109
Joined: Mon Dec 31, 2007 10:39 am
Location: New Jersey

Re: Working on Reels - Tips!

Postby uljersey » Fri Dec 07, 2018 3:01 pm

After having to disassemble the sink trap to recover a tiny bushing I came up with this. Dollar store kitchen sink drain strainer, the lid from an electrical tape package and binder clips. All small parts go inside and can be submerged, agitated, rinsed and excess water shaken off. I've been using this thing for years now and it hasn't let me down yet.

Image

Image


Return to “Maintenance & SuperTuning Q&A”

Who is online

Users browsing this forum: Google [Bot] and 7 guests